Allyl bromide
Product identifier
- Product name: Allyl bromide
- CBnumber: CB7852691
- CAS: 106-95-6
- EINECS Number: 203-446-6
- Synonyms: allyl bromide,3-Bromopropene
Relevant identified uses of the substance or mixture and uses advised against
- Relevant identified uses: For R&D use only. Not for medicinal, household or other use.
- Uses advised against: none
Company Identification
- Company: Chemicalbook
- Address: Building 1, Huihuang International, Shangdi 10th Street, Haidian District, Beijing
- Telephone: 400-158-6606
GHS Label elements, including precautionary statements
-
Symbol(GHS)
- Signal wordDanger
Substance
- Product name: Allyl bromide
- Synonyms: allyl bromide,3-Bromopropene
- CAS: 106-95-6
- EC number: 203-446-6
- MF: C3H5Br
- MW: 120.98
Description of first aid measures
General adviceMost important symptoms and effects, both acute and delayed
Indication of any immediate medical attention and special treatment needed
Extinguishing media
Suitable extinguishing mediaSpecial hazards arising from the substance or mixture
Carbon oxides Hydrogen bromide gas
Flash back possible over considerable distance., Container explosion may occur under fire conditions.
Advice for firefighters
Wear self-contained breathing apparatus for firefighting if necessary.
Further information
Use water spray to cool unopened containers.
NFPA 704
| HEALTH | 3 | Short exposure could cause serious temporary or moderate residual injury (e.g. liquid hydrogen, sulfuric acid, calcium hypochlorite, hexafluorosilicic acid) | |
| FIRE | 3 | Liquids and solids (including finely divided suspended solids) that can be ignited under almost all ambient temperature conditions . Liquids having a flash point below 22.8 °C (73 °F) and having a boiling point at or above 37.8 °C (100 °F) or having a flash point between 22.8 and 37.8 °C (73 and 100 °F). (e.g. gasoline, acetone) | |
| REACT | 1 | Normally stable, but can become unstable at elevated temperatures and pressures (e.g. propene) | |
| SPEC. HAZ. |
Personal precautions, protective equipment and emergency procedures
Wear respiratory protection. Avoid breathing vapors, mist or gas. Ensure adequate ventilation. Remove all sources of ignition. Evacuate personnel to safe areas. Beware of vapors accumulating to form explosive concentrations. Vapors can accumulate in low areas.
For personal protection see section 8.
Environmental precautions
Prevent further leakage or spillage if safe to do so. Do not let product enter drains. Discharge into the environment must be avoided.
Methods and materials for containment and cleaning up
Contain spillage, and then collect with an electrically protected vacuum cleaner or by wet- brushing and place in container for disposal according to local regulations (see section 13).
Reference to other sections
For disposal see section 13.
Precautions for safe handling
Advice on safe handling
Avoid exposure - obtain special instructions before use. Advice on safe handling
Avoid contact with skin and eyes. Avoid inhalation of vapor or mist.
Advice on protection against fire and explosion
Keep away from sources of ignition - No smoking.Take measures to prevent the build up of electrostatic charge.
Hygiene measures
Avoid contact with skin, eyes and clothing. Wash hands before breaks and immediately after handling the product.
For precautions see section 2.2.
Conditions for safe storage, including any incompatibilities
Storage conditions
Store in cool place. Keep container tightly closed in a dry and well-ventilated place. Containers which are opened must be carefully resealed and kept upright to prevent leakage.
Storage stability
Recommended storage temperature 2 - 8 °C
Moisture sensitive. Light sensitive.
Specific end use(s)
Apart from the uses mentioned in section 1.2 no other specific uses are stipulated
control parameter
Hazard composition and occupational exposure limitsExposure controls
Personal protective equipmentTightly fitting safety goggles. Faceshield (8-inch minimum). Use equipment for eye
protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU).
Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique (without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands.
The selected protective gloves have to satisfy the specifications of Regulation (EU) 2016/425 and the standard EN 374 derived from it.
Full contact
Material: Fluorinated rubber Minimum layer thickness: 0,7 mm Break through time: 480 min
Material tested:Vitoject? (KCL 890 / Aldrich Z677698, Size M)
Splash contact
Material: Fluorinated rubber
Minimum layer thickness: 0,7 mm Break through time: 480 min
Material tested:Vitoject? (KCL 890 / Aldrich Z677698, Size M)
data source: KCL GmbH, D-36124 Eichenzell, phone +49 (0)6659 87300, e-mail sales@kcl.de, test method: EN374
If used in solution, or mixed with other substances, and under conditions which differ from EN 374, contact the supplier of the EC approved gloves. This recommendation is advisory only and must be evaluated by an industrial hygienist and safety officer familiar with the specific situation of anticipated use by our customers. It should not be construed as offering an approval for any specific use scenario.
Complete suit protecting against chemicals, Flame retardant antistatic protective clothing., The type of protective equipment must be selected according to the concentration and amount of the dangerous substance at the specific workplace.
Where risk assessment shows air-purifying respirators are appropriate use a full- face respirator with multi-purpose combination (US) or type ABEK (EN 14387) respirator cartridges as a backup to engineering controls. If the respirator is the sole means of protection, use a full-face supplied air respirator. Use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU).
Prevent further leakage or spillage if safe to do so. Do not let product enter drains. Discharge into the environment must be avoided.
Information on basic physicochemical properties
- Appearancecolorless clear, liquid
- Odourunpleasant
- Odour ThresholdNo data available
- pHNo data available
- Melting point/freezing pointMelting point/range: -119 °C
- Initial boiling point and boiling range70 - 71 °C
- Flash point-1 °C - closed cup
- Evaporation rateNo data available
- Flammability (solid, gas)No data available
- Upper/lower flammability or explosive limits Upper explosion limit: 7,3 %(V) Lower explosion limit: 4,3 %(V)
- Vapour pressure No data available
- Vapour density 4.2 (vs air)
- Relative density1.398
- Water solubility3,83 g/l at 25 °C
- Partition coefficient: n-octanol/waterlog Pow: 1,79 at 20 °C
- Autoignition temperatureNo data available
- Decomposition temperatureNo data available
- ViscosityViscosity, kinematic: No data available Viscosity, dynamic: No data available
- Explosive propertiesNo data available
- Oxidizing propertiesNo data available
Other safety information
No data available
Reactivity
No data available
Chemical stability
Stable under recommended storage conditions. Contains the following stabilizer(s):
propylene oxide (<=0,1 %)
Possibility of hazardous reactions
No data available
Conditions to avoid
May polymerize on exposure to light. Exposure to moisture. Exposure to air. Heat, flames and sparks.
Incompatible materials
Oxidizing agents, Alkali metals, Alkaline earth metals, Light metals, Amides, Amines, Powdered metals
Hazardous decomposition products
In the event of fire: see section 5
Information on toxicological effects
Acute toxicityLD50 Oral - Rat - male and female - 200 mg/kg (OECD Test Guideline 401)
Acute toxicity estimate Inhalation - 4 h - 2,41 mg/l (Calculation method)
LC50 Inhalation - Rat - male and female - 4 h - 2,41 mg/l (OECD Test Guideline 403)
Acute toxicity estimate Dermal - > 2.000 mg/kg (Calculation method)
Result: Causes burns. (OECD Test Guideline 404)
Test system: S. typhimurium
Metabolic activation: with and without metabolic activation Method: US-EPA
Result: positive
Test Type: Micronucleus test Species: Mouse
Application Route: Oral Method: US-EPA Result: negative
Toxicity
(OECD Test Guideline 201)
Persistence and degradability
Biodegradability Result: - Readily biodegradable.
Remarks: (External MSDS)
Bioaccumulative potential
No data available
Mobility in soil
No data available
Results of PBT and vPvB assessment
PBT/vPvB assessment not available as chemical safety assessment not required/not conducted
Other adverse effects
Forms toxic mixtures in water, dilution measures notwithstanding. Discharge into the environment must be avoided.
Waste treatment methods
Product
Burn in a chemical incinerator equipped with an afterburner and scrubber but exert extra care in igniting as this material is highly flammable. Offer surplus and non-recyclable solutions to a licensed disposal company.
IncompatibilitiesVapor may form explosive mixture with air. Incompatible with oxidizers (chlorates, nitrates, peroxides, permanganates, perchlorates, chlorine, bromine, fluorine, etc.); contact may cause fires or explosions. Keep away from alkaline materials, strong bases, strong acids, oxoacids, epoxides. Heat or light exposure may cause decomposition and corrosive vapors.
Waste DisposalIn accordance with 40CFR 165 recommendations for the disposal of pesticides and pesticide containers. Must be disposed properly by following package label directions or by contacting your local or federal environmental control agency, or by contacting your regional EPA office.
Contaminated packaging
Dispose of as unused product.
UN number
ADR/RID: 1099 IMDG: 1099 IATA: 1099
UN proper shipping name
Passenger Aircraft: Not permitted for transport
Transport hazard class(es)
ADR/RID: 3 (6.1) IMDG: 3 (6.1) IATA: 3 (6.1)
Packaging group
ADR/RID: I IMDG: I IATA: I
Environmental hazards
ADR/RID: yes IMDG Marine pollutant: yes IATA: no
Special precautions for user
No data available
Safety, health and environmental regulations/legislation specific for the substance or mixture
Regulations on the Safety Management of Hazardous ChemicalsAbbreviations and acronyms
- CAS: Chemical Abstracts Service
- ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
- RID: Regulation concerning the International Carriage of Dangerous Goods by Rail
- IMDG: International Maritime Dangerous Goods
- IATA: International Air Transportation Association
- TWA: Time Weighted Average
- STEL: Short term exposure limit
- LC50: Lethal Concentration 50%
- LD50: Lethal Dose 50%
- EC50: Effective Concentration 50%
References
【1】CAMEO Chemicals, website: http://cameochemicals.noaa.gov/search/simple
【2】ChemIDplus, website: http://chem.sis.nlm.nih.gov/chemidplus/chemidlite.jsp
【3】ECHA - European Chemicals Agency, website: https://echa.europa.eu/
【4】eChemPortal - The Global Portal to Information on Chemical Substances by OECD, website: http://www.echemportal.org/echemportal/index?pageID=0&request_locale=en
【5】ERG - Emergency Response Guidebook by U.S. Department of Transportation, website: http://www.phmsa.dot.gov/hazmat/library/erg
【6】Germany GESTIS-database on hazard substance, website: http://www.dguv.de/ifa/gestis/gestis-stoffdatenbank/index-2.jsp
【7】HSDB - Hazardous Substances Data Bank, website: https://toxnet.nlm.nih.gov/newtoxnet/hsdb.htm
【8】IARC - International Agency for Research on Cancer, website: http://www.iarc.fr/
【9】IPCS - The International Chemical Safety Cards (ICSC), website: http://www.ilo.org/dyn/icsc/showcard.home
【10】Sigma-Aldrich, website: https://www.sigmaaldrich.com/
The information in this MSDS is only applicable to the specified product, unless otherwise specified, it is not applicable to the mixture of this product and other substances. This MSDS only provides information on the safety of the product for those who have received the appropriate professional training for the user of the product. Users of this MSDS must make independent judgments on the applicability of this SDS. The authors of this MSDS will not be held responsible for any harm caused by the use of this MSDS.